TB20 bus coupler EtherNet/IP
A functioning TB20 configuration will always require a bus coupler and at least one peripheral module.
Note: Individual modules cannot be combined with the IO systems of other manufacturers.
€201.14
TB20 bus coupler EtherNet/IP
The EtherNet/IP bus coupler makes it possible to access data from peripheral modules using the EtherNet/IP protocol. It can accommodate up to 64 modules of any kind connected in series with the bus coupler.
The EtherNet/IP bus coupler features an integrated two-port switch that allows for star and line topology configurations.
A large I/O image table size of one kbyte makes it possible to implement comprehensive and complex systems.
TB20 ToolBox can be used to easily configure the system and the various module parameters and transfer the corresponding settings to the coupler.
A functioning TB20 configuration will always require a bus coupler and at least one peripheral module. The bus coupler supports hot-swapping for replacing modules during operation.
Note: Individual modules cannot be combined with the IO systems of other manufacturers.
- Modules can be replaced during operation (hot-swapping)
- 24 V DC power supply
- Integrated power supply unit for powering peripheral modules (2.5 A)
- Supplies the system’s I/O voltage (24 VDC)
- USB device port for online diagnostics, configuring parameters, setup, and firmware updates with "TB20 ToolBox"
- TB20 ToolBox simulation for commissioning the I/O system without a higher-level controller in order to test the functionality (I/O check)
- Concealed "factory reset" switch for restoring the module to its factory settings
- Supports unicast and multicast
- CIP connections
- 511 bytes of input assembly data, 511 bytes of output assembly data
- TB20 ToolBox can be used for easy access to assembly sizes and to the structure of the memory image within the assemblies
- Up to 64 peripheral modules
- Implicit messaging (transport class 1)
- Explicit messaging (transport class 3)
- TCP watchdog
- IP address can be set relative to a base IP address by using a DIP switch that can be covered
- DHCP (can be selected using DIP switch)
- Integrated 2-port switch with 2 x RJ45 connectors
- Module process data is automatically assigned to the EtherNet/IP mapping
TB20 bus coupler EtherNet/IP
General information
- Order number600-175-1AA11
- Article nameTB20-C, EtherNet/IP bus coupler
- Scope of deliveryBus coupler Ethernet/IP, 24 V power supply connector, bus cover element, base module
- Dimensions (DxWxH)73 x 35 x 110 mm
- WeightApprox. 115 g
- Number of modules that can be connected in series64
- Voltage supply24 VDC, 18–28 VDC
- Power dissipationMax. 8 W
- Permissible cable cross-sectionAWG 16 .. 22
- Mounting positionAny
EtherNet/IP interface
- Number2
- ConnectionRJ45
- Protocol transmission modelImplicit messaging (transport class 1), explicit messaging (transport class 3)
- Transmission rate10/100 Mbps, automatic detection
- Input/output assembly size511/511 bytes
- IP addressCan be set with software and/or DIP switch
- DHCPYes, can be selected using DIP switch
USB interface
- Number1
- ProtocolFull-speed USB 1.1 device
- ConnectionMini-USB
- Isolation voltageYes
- Electrical isolation1.5 kV
Current draw
- Current draw without modules (internal)75 mA
- Power supply for modules5 V DC, max 2.5 A
Ambient conditions
- Ambient temperature0 °C … +60 °C
- Transport and storage temperature-20 °C … +80 °C
- Relative air humidity95 % r H without condensation
- Protection ratingIP 20
- CertificationsCE, UL
UL
- Surrounding Air Temperature0 °C … +50 °C
- Pollution degree2
CE
- Noise immunityDIN EN 61000-6-2 “EMC Immunity”
- Interference emissionDIN EN 61000-6-4 “EMC Emission”
- Vibration and shock resistanceDIN EN 60068-2-6:2008 „Vibration“, DIN EN 60068-2-27:2010 „Shock"
TB20 bus coupler EtherNet/IP
| Name | Version | Size |
| TB20, Manual EtherNet/IP Bus Coupler | 3 | 9 MB |
| EU Declaration of Confirmity | 04-2020 | 55 KB |
| Name | Version | Size |
| Flyer, TB20 IO-system for numerous applications | 08-2022 | 6 MB |
| Name | Version | Size |
| TB20, EDS file for EtherNet/IP Bus Coupler | 1.1 | 3 KB |
| TB20-ToolBox V2 Setup | V2.10.008 | 29 MB |
| Name | Version | Size |
| TB20, USB Driver | 1.20 | 7 KB |
| Name | Version | Size |
| TB20, Macros for EPLAN Electric P8* from V2.0 in EDZ format | 07.02.2018 | 84 MB |
| TB20, STEP files | 1.00 | 8 MB |
| TB20-C, Buskoppler EtherNet/IP, STEP Files | 5 MB |
TB20 bus coupler EtherNet/IP
The EtherNet/IP bus coupler makes it possible to access data from peripheral modules using the EtherNet/IP protocol. It can accommodate up to 64 modules of any kind connected in series with the bus coupler.
The EtherNet/IP bus coupler features an integrated two-port switch that allows for star and line topology configurations.
A large I/O image table size of one kbyte makes it possible to implement comprehensive and complex systems.
TB20 ToolBox can be used to easily configure the system and the various module parameters and transfer the corresponding settings to the coupler.
A functioning TB20 configuration will always require a bus coupler and at least one peripheral module. The bus coupler supports hot-swapping for replacing modules during operation.
Note: Individual modules cannot be combined with the IO systems of other manufacturers.
- Modules can be replaced during operation (hot-swapping)
- 24 V DC power supply
- Integrated power supply unit for powering peripheral modules (2.5 A)
- Supplies the system’s I/O voltage (24 VDC)
- USB device port for online diagnostics, configuring parameters, setup, and firmware updates with "TB20 ToolBox"
- TB20 ToolBox simulation for commissioning the I/O system without a higher-level controller in order to test the functionality (I/O check)
- Concealed "factory reset" switch for restoring the module to its factory settings
- Supports unicast and multicast
- CIP connections
- 511 bytes of input assembly data, 511 bytes of output assembly data
- TB20 ToolBox can be used for easy access to assembly sizes and to the structure of the memory image within the assemblies
- Up to 64 peripheral modules
- Implicit messaging (transport class 1)
- Explicit messaging (transport class 3)
- TCP watchdog
- IP address can be set relative to a base IP address by using a DIP switch that can be covered
- DHCP (can be selected using DIP switch)
- Integrated 2-port switch with 2 x RJ45 connectors
- Module process data is automatically assigned to the EtherNet/IP mapping
TB20 bus coupler EtherNet/IP
General information
- Order number600-175-1AA11
- Article nameTB20-C, EtherNet/IP bus coupler
- Scope of deliveryBus coupler Ethernet/IP, 24 V power supply connector, bus cover element, base module
- Dimensions (DxWxH)73 x 35 x 110 mm
- WeightApprox. 115 g
- Number of modules that can be connected in series64
- Voltage supply24 VDC, 18–28 VDC
- Power dissipationMax. 8 W
- Permissible cable cross-sectionAWG 16 .. 22
- Mounting positionAny
EtherNet/IP interface
- Number2
- ConnectionRJ45
- Protocol transmission modelImplicit messaging (transport class 1), explicit messaging (transport class 3)
- Transmission rate10/100 Mbps, automatic detection
- Input/output assembly size511/511 bytes
- IP addressCan be set with software and/or DIP switch
- DHCPYes, can be selected using DIP switch
USB interface
- Number1
- ProtocolFull-speed USB 1.1 device
- ConnectionMini-USB
- Isolation voltageYes
- Electrical isolation1.5 kV
Current draw
- Current draw without modules (internal)75 mA
- Power supply for modules5 V DC, max 2.5 A
Ambient conditions
- Ambient temperature0 °C … +60 °C
- Transport and storage temperature-20 °C … +80 °C
- Relative air humidity95 % r H without condensation
- Protection ratingIP 20
- CertificationsCE, UL
UL
- Surrounding Air Temperature0 °C … +50 °C
- Pollution degree2
CE
- Noise immunityDIN EN 61000-6-2 “EMC Immunity”
- Interference emissionDIN EN 61000-6-4 “EMC Emission”
- Vibration and shock resistanceDIN EN 60068-2-6:2008 „Vibration“, DIN EN 60068-2-27:2010 „Shock"
TB20 bus coupler EtherNet/IP
| Name | Version | Size |
| TB20, Manual EtherNet/IP Bus Coupler | 3 | 9 MB |
| EU Declaration of Confirmity | 04-2020 | 55 KB |
| Name | Version | Size |
| Flyer, TB20 IO-system for numerous applications | 08-2022 | 6 MB |
| Name | Version | Size |
| TB20, EDS file for EtherNet/IP Bus Coupler | 1.1 | 3 KB |
| TB20-ToolBox V2 Setup | V2.10.008 | 29 MB |
| Name | Version | Size |
| TB20, USB Driver | 1.20 | 7 KB |
| Name | Version | Size |
| TB20, Macros for EPLAN Electric P8* from V2.0 in EDZ format | 07.02.2018 | 84 MB |
| TB20, STEP files | 1.00 | 8 MB |
| TB20-C, Buskoppler EtherNet/IP, STEP Files | 5 MB |