TB20 bus coupler PROFIBUS-DP
A functioning TB20 configuration will always require a bus coupler and at least one peripheral module.
Note: Individual modules cannot be combined with the IO systems of other manufacturers.
€188.96
TB20 bus coupler PROFIBUS-DP
The PROFIBUS-DP bus coupler is designed to connect a PROFIBUS bus to TB20 peripheral modules. It supports the DP-V0 and DP-V1 protocols.
It will recognize all connected peripheral modules and assign each module the corresponding inputs/outputs from the process image table.
A functioning TB20 configuration will always require a bus coupler and at least one peripheral module, but can accommodate up to 64 modules of any kind connected in series with the bus coupler. The bus coupler supports hot-swap for replacing modules during operation.
Bit packing:
Starting with firmware version 1.20, the states of 2-bit and 4-bit I/O modules can be packed together in bytes, making it possible to take full advantage of all the space in the process image table.
Parameters
Diagnostic alarm: On | Off
Process alarm: On | Off
Pull/plug alarm: On | Off
Startup when expected/actual configuration differ: On | Off (hot-swaping allowed: Yes | No)
Identifier-related diagnostics: On | Off
Submodule status: On | Off
Channel-related diagnostics: On | Off
Note: Individual modules cannot be combined with the IO systems of other manufacturers.
- Modules can be replaced during operation (hot-swapping)
- 24 VDC power supply
- Integrated power supply unit for powering peripheral modules (2.5 A)
- Supplies the system’s I/O voltage (24 VDC)
- USB device port for online diagnostics, configuring parameters, setup, and firmware updates with TB20 ToolBox
- TB20 ToolBox simulation for setting up the I/O system without a higher-level controller in order to test the system`s operation (I/O check)
- PROFIBUS DP slave as defined in EN 50170/IEC 61158
- Supports all PROFIBUS baud rates
- DP-V0 and DP-V1 support
- Up to 64 peripheral modules
- Up to 244 bytes of input data and 244 bytes of output data
- One class 1 master connection with 240 bytes of payload data
- Up to three class 2 master connections with 240 bytes of payload data (as a DP-V1 slave)
- I&M data
- 3 LEDs, one of them bi-color
- Concealed "factory reset" switch for restoring the module to its factory settings
TB20 bus coupler PROFIBUS-DP
General information
- Order number600-151-1AA11
- Article nameTB20-C, PROFIBUS-DP bus coupler
- Scope of deliveryBus coupler PROFIBUS-DP, 24 V power supply connector, bus cover element, base module
- Dimensions (DxWxH)73 x 35 x 110 mm
- WeightApprox. 115 g
- Number of modules that can be connected in series64
- Voltage supply24 VDC, 18–28 VDC
- Power dissipationMax. 8 W
- Permissible cable cross-sectionAWG 16 .. 22
- Mounting positionAny
PROFIBUS interface
- Number1
- ProtocolPROFIBUS DP/V0 & DP/V1
- Transmission rate9.6 Kbaud ... 12 Mbaud, automatic detection
- I/O image size244/244 bytes
- Parameter configuration length244 bytes
- InterfaceRS485
- Connection9-pin D-sub female connector
USB interface
- Number1
- ProtocolFull-speed USB 1.1 device
- ConnectionMini-USB
- Isolation voltage1.5 kV
- Electrical isolationYes
Current draw
- Current draw without modules (internal)75 mA
- Power supply for modules5 V DC, max 2.5 A
Ambient conditions
- Ambient temperature0 °C … +60 °C
- Transport and storage temperature-20 °C … +80 °C
- Relative air humidity95 % r H without condensation
- Protection ratingIP 20
- CertificationsCE, UL
UL
- Surrounding Air Temperature0 °C … +50 °C
- Pollution degree2
CE
- Noise immunityDIN EN 61000-6-2 “EMC Immunity”
- Interference emissionDIN EN 61000-6-4 “EMC Emission”
- Vibration and shock resistanceDIN EN 60068-2-6:2008 „Vibration“, DIN EN 60068-2-27:2010 „Shock"
TB20 bus coupler PROFIBUS-DP
| Name | Version | Size |
| TB20, Manual PROFIBUS-DP Bus Coupler | 5 | 10 MB |
| EU Declaration of Confirmity | 04-2020 | 55 KB |
| Name | Version | Size |
| Flyer, TB20 IO-system for numerous applications | 08-2022 | 6 MB |
| Name | Version | Size |
| TB20, GSD file for PROFIBUS-DP Bus Coupler | 1.50 | 75 KB |
| TB20-ToolBox V2 Setup | V2.10.008 | 29 MB |
| Name | Version | Size |
| TB20, USB Driver | 1.20 | 7 KB |
| Name | Version | Size |
| TB20, Macros for EPLAN Electric P8* from V2.0 in EDZ format | 07.02.2018 | 84 MB |
| TB20, STEP files | 1.00 | 8 MB |
| TB20-C, Buskoppler PROFIBUS-DP, STEP Files | 5 MB |
TB20 bus coupler PROFIBUS-DP
The PROFIBUS-DP bus coupler is designed to connect a PROFIBUS bus to TB20 peripheral modules. It supports the DP-V0 and DP-V1 protocols.
It will recognize all connected peripheral modules and assign each module the corresponding inputs/outputs from the process image table.
A functioning TB20 configuration will always require a bus coupler and at least one peripheral module, but can accommodate up to 64 modules of any kind connected in series with the bus coupler. The bus coupler supports hot-swap for replacing modules during operation.
Bit packing:
Starting with firmware version 1.20, the states of 2-bit and 4-bit I/O modules can be packed together in bytes, making it possible to take full advantage of all the space in the process image table.
Parameters
Diagnostic alarm: On | Off
Process alarm: On | Off
Pull/plug alarm: On | Off
Startup when expected/actual configuration differ: On | Off (hot-swaping allowed: Yes | No)
Identifier-related diagnostics: On | Off
Submodule status: On | Off
Channel-related diagnostics: On | Off
Note: Individual modules cannot be combined with the IO systems of other manufacturers.
- Modules can be replaced during operation (hot-swapping)
- 24 VDC power supply
- Integrated power supply unit for powering peripheral modules (2.5 A)
- Supplies the system’s I/O voltage (24 VDC)
- USB device port for online diagnostics, configuring parameters, setup, and firmware updates with TB20 ToolBox
- TB20 ToolBox simulation for setting up the I/O system without a higher-level controller in order to test the system`s operation (I/O check)
- PROFIBUS DP slave as defined in EN 50170/IEC 61158
- Supports all PROFIBUS baud rates
- DP-V0 and DP-V1 support
- Up to 64 peripheral modules
- Up to 244 bytes of input data and 244 bytes of output data
- One class 1 master connection with 240 bytes of payload data
- Up to three class 2 master connections with 240 bytes of payload data (as a DP-V1 slave)
- I&M data
- 3 LEDs, one of them bi-color
- Concealed "factory reset" switch for restoring the module to its factory settings
TB20 bus coupler PROFIBUS-DP
General information
- Order number600-151-1AA11
- Article nameTB20-C, PROFIBUS-DP bus coupler
- Scope of deliveryBus coupler PROFIBUS-DP, 24 V power supply connector, bus cover element, base module
- Dimensions (DxWxH)73 x 35 x 110 mm
- WeightApprox. 115 g
- Number of modules that can be connected in series64
- Voltage supply24 VDC, 18–28 VDC
- Power dissipationMax. 8 W
- Permissible cable cross-sectionAWG 16 .. 22
- Mounting positionAny
PROFIBUS interface
- Number1
- ProtocolPROFIBUS DP/V0 & DP/V1
- Transmission rate9.6 Kbaud ... 12 Mbaud, automatic detection
- I/O image size244/244 bytes
- Parameter configuration length244 bytes
- InterfaceRS485
- Connection9-pin D-sub female connector
USB interface
- Number1
- ProtocolFull-speed USB 1.1 device
- ConnectionMini-USB
- Isolation voltage1.5 kV
- Electrical isolationYes
Current draw
- Current draw without modules (internal)75 mA
- Power supply for modules5 V DC, max 2.5 A
Ambient conditions
- Ambient temperature0 °C … +60 °C
- Transport and storage temperature-20 °C … +80 °C
- Relative air humidity95 % r H without condensation
- Protection ratingIP 20
- CertificationsCE, UL
UL
- Surrounding Air Temperature0 °C … +50 °C
- Pollution degree2
CE
- Noise immunityDIN EN 61000-6-2 “EMC Immunity”
- Interference emissionDIN EN 61000-6-4 “EMC Emission”
- Vibration and shock resistanceDIN EN 60068-2-6:2008 „Vibration“, DIN EN 60068-2-27:2010 „Shock"
TB20 bus coupler PROFIBUS-DP
| Name | Version | Size |
| TB20, Manual PROFIBUS-DP Bus Coupler | 5 | 10 MB |
| EU Declaration of Confirmity | 04-2020 | 55 KB |
| Name | Version | Size |
| Flyer, TB20 IO-system for numerous applications | 08-2022 | 6 MB |
| Name | Version | Size |
| TB20, GSD file for PROFIBUS-DP Bus Coupler | 1.50 | 75 KB |
| TB20-ToolBox V2 Setup | V2.10.008 | 29 MB |
| Name | Version | Size |
| TB20, USB Driver | 1.20 | 7 KB |
| Name | Version | Size |
| TB20, Macros for EPLAN Electric P8* from V2.0 in EDZ format | 07.02.2018 | 84 MB |
| TB20, STEP files | 1.00 | 8 MB |
| TB20-C, Buskoppler PROFIBUS-DP, STEP Files | 5 MB |